Kramer-electronics VS-88DVI User Manual

KRAMER ELECTRONICS LTD. USER MANUAL MODEL: VS-88DVI 8x8 DVI Matrix Switcher P/N: 2900-000592 Rev 3

VS-88DVI - Overview 7 3.2 Using the IR Transmitter You can use the RC-IR3 IR transmitter to control the machine via the built-in IR receiver on th

8 VS-88DVI - Installing in a Rack 4 Installing in a Rack This section provides instructions for rack mounting the unit.

VS-88DVI - Connecting the VS-88DVI 9 5 Connecting the VS-88DVI Always switch off the power to each device before connecting it to your VS-88DVI.

10 VS-88DVI - Connecting the VS-88DVI Figure 3: Connecting the VS-88DVI 8x8 DVI Matrix Switcher

VS-88DVI - Operating the VS-88DVI 11 6 Operating the VS-88DVI This section describes how to: • Route inputs to outputs (see Section 6.1) • Dis

12 VS-88DVI - Operating the VS-88DVI Figure 4: SELECTOR Buttons The gray numbers (1 to 16) in Figure 4 that illustrate the corresponding store/rec

VS-88DVI - Operating the VS-88DVI 13 6.4 Acquiring the EDID You can acquire the EDID from: • A single connected output (see Section 6.4.1) • Se

14 VS-88DVI - Operating the VS-88DVI 6.4.2 Acquiring an EDID from Several Sets of Inputs and Outputs To acquire the EDID from several sets of inpu

VS-88DVI - Operating the VS-88DVI 15 6.4.3 Acquiring the Default EDID To reset to the default EDID, do the following: 1. Turn ON the VS-88DVI. 2.

16 VS-88DVI - Operating the VS-88DVI Method B—Connect the RS-232 9-pin D-sub port on the unit via a straight (flat) cable to the null-modem adapter

VS-88DVI - Operating the VS-88DVI 17 Figure 6: Local Area Connection Properties Window 6. Select Use the following IP Address, and fill in the de

18 VS-88DVI - Operating the VS-88DVI 6.6.2 Connecting the Ethernet Port via a Network Hub (Straight-Through Cable) You can connect the Ethernet po

VS-88DVI - Technical Specifications 19 7 Technical Specifications INPUTS: 8 DVI, 1.2Vpp on DVI Molex 24-pin female connectors; DDC signal 5Vpp (T

20 VS-88DVI - Hex Table 8 Hex Table The following table lists the Hex values for a single machine (MACHINE # 1): Switching Video Channels OUT 8

VS-88DVI - Protocol 2000 21 9 Protocol 2000 This RS-232/RS-485 communication protocol uses four bytes of information as defined below. For RS-232,

22 VS-88DVI - Protocol 2000 9.2 Instruction Codes All the values in the table are decimal, unless otherwise stated Instruction Codes for Protocol

VS-88DVI - Protocol 2000 23 NOTE 8 – The reply is as in NOTE 4 above, except that the OUTPUT is assigned with the value 0 if the setup is not defin

For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We

VS-88DVI – Contents i Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions 3 2.3 Re

VS-88DVI - Introduction 1 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creat

2 VS-88DVI - Getting Started 2 Getting Started We recommend that you: • Unpack the equipment carefully and save the original box and packaging ma

VS-88DVI - Getting Started 3 2.2 Safety Instructions Caution: There are no operator serviceable parts inside the unit Warning: Use only the pow

4 VS-88DVI - Overview 3 Overview The VS−88DVI is a high−performance matrix switcher for DVI signals. The unit reclocks and equalizes the signal an

VS-88DVI - Overview 5 VS-88DVI – Overview 5 Figure 1: VS-88DVI 8x8 DVI Matrix Switcher Front Panel # Feature Function 1 IR Receiver LED The

6 VS-88DVI - Overview Figure 2: VS-88DVI 8x8 DVI Matrix Switcher Rear Panel # Feature Function 12 OUT DVI Connectors Connect to the DVI accept