Kramer Electronics, Ltd. USER MANUAL Model: SV-552/SV-552 ALC SummitView™ Processor/Switcher
KRAMER: SIMPLE CREATIVE TECHNOLOGY Defining the SV-552 Processor/Switcher 6 PART II The SV-552 SummitView™ Processor/Switcher PART II defines the S
Defining the SV-552 Processor/Switcher 7 Figure 1 and Table 2 define the front and rear panels of the SV-552 SummitView™ Processor/ Switcher. Figure
KRAMER: SIMPLE CREATIVE TECHNOLOGY Defining the SV-552 Processor/Switcher 8 Table 2: SV-552 SummitView™ Processor/Switcher Underside Features # Feat
Defining the SV-552 Processor/Switcher 9 # Feature Function 24 RS-485 Terminal Block Connect to the RS-485 detachable terminal block on a RS-485
KRAMER: SIMPLE CREATIVE TECHNOLOGY Connecting the SV-552 SummitView™ Processor/ Switcher 10 this information exchange is essential for proper VGA OU
Connecting the SV-552 SummitView™ Processor/ Switcher 11 Figure 3: Connecting the SV-552 For instructions on wiring the K-Net connector, see Section
KRAMER: SIMPLE CREATIVE TECHNOLOGY Connecting the SV-552 SummitView™ Processor/ Switcher 12 5.3 Installing the SV-552 in a 19” Rack (Optional) This
The RC-63DL Room Controller 13 6 The RC-63DL Room Controller The RC-63DL is a room control panel that can be used independently or as a user interf
KRAMER: SIMPLE CREATIVE TECHNOLOGY The RC-63DL Room Controller 14 Figure 4: RC-63DL Room Controller Front Panel Table 4: RC-63DL Room Controller Fr
The RC-63DL Room Controller 15 Table 5: RC-63DL Room Controller Rear Panel Features # Feature Function 1 FIRMWARE UPGRADE Switch For technical supp
Contents i Contents 1 Introduction 1 2 Getting Started 1 PART I Your SummitView™ System 2 3 Overview 2 3.1 Basic SummitView™ SV-552 Installa
KRAMER: SIMPLE CREATIVE TECHNOLOGY Defining and Connecting the Wall Plates 16 Figure 6: Connecting the RC-63DL to the SV-552 SummitView™ Processor/
Defining and Connecting the Wall Plates 17 Advanced User Tip The SV-302 and SV-306 IR OUT port enables remote IR control (this requires the appropri
KRAMER: SIMPLE CREATIVE TECHNOLOGY Defining and Connecting the Wall Plates 18 EDID information can be stored in the wall plate by using the FC-200 X
Defining and Connecting the Wall Plates 19 7.1.2 Defining the SV-302 (U.S.) The SV-302 is a single-gang wall plate insert. Table 8 defines the front
KRAMER: SIMPLE CREATIVE TECHNOLOGY Defining and Connecting the Wall Plates 20 7.1.3 Defining the SV-306 (U.S.) The SV-306 is a single-gang wall pla
Defining and Connecting the Wall Plates 21 7.1.4 Defining the SV-307 (U.S.) The SV307 is a triple-gang wall plate. Table 10 defines the front and re
KRAMER: SIMPLE CREATIVE TECHNOLOGY Defining and Connecting the Wall Plates 22 7.2 Defining the Wall Plates (England and Europe1) This section define
Defining and Connecting the Wall Plates 23 EDID information can be stored in the wall plate by using the FC-200 XGA EDID Copier Kramer Tool (see the
KRAMER: SIMPLE CREATIVE TECHNOLOGY Defining and Connecting the Wall Plates 24 7.2.3 Defining the SV-306 (England and Europe) The SV-306 is a single
Defining and Connecting the Wall Plates 25 7.3 Connecting the Wall Plates to the SV-552 The wall plates are connected to the corresponding inputs on
KRAMER: SIMPLE CREATIVE TECHNOLOGY Contents ii 10.1 Backlit Buttons 32 10.2 Button Label Sheet 32 11 SummitView™ System Cables 33 12 SummitVi
KRAMER: SIMPLE CREATIVE TECHNOLOGY Defining and Connecting the Wall Plates 26 Kramer C-GMA/GMA cable (VGA HD15M +Audio connector to VGA HD15M +Audio
Defining and Connecting the Wall Plates 27 2. On the rear of the SV-302, connect the RJ-45 CAT 5 connector to either input VIDEO 1 or VIDEO 2 input
KRAMER: SIMPLE CREATIVE TECHNOLOGY Wiring the TP Line In/Line Out Connectors 28 8 Wiring the TP Line In/Line Out Connectors STP cabling1 with a len
Wiring the TP Line In/Line Out Connectors 29 Table 14: UTP Pinout (U.S.) EIA /TIA 568B PIN Wire Color 1 Orange/White 2 Orange 3 Green/White 4 Bl
KRAMER: SIMPLE CREATIVE TECHNOLOGY Grounding the Wall Plate 30 • Each wire protrudes 9mm in length from the plastic insulation so that it can be ea
Grounding the Wall Plate 31 Figure 10: Wiring the K-Net Connector
KRAMER: SIMPLE CREATIVE TECHNOLOGY Customizing the Controllers' Buttons and Labels 32 PART IV Further information PART IV includes further inf
SummitView™ System Cables 33 11 SummitView™ System Cables Table 17 defines the recommended cables for a SummitView™ installation. Table 17: Recomme
KRAMER: SIMPLE CREATIVE TECHNOLOGY SummitView™ Cable Termination 34 12 SummitView™ Cable Termination Table 18 defines the SummitView™ cable termina
SummitView™ Cable Termination 35 Figure 12: Stickers Affixed to Cables
Contents iii Tables Table 1: Quick Installation Guide for the SummitView™ Basic System 4Table 2: SV-552 SummitView™ Processor/Switcher Underside F
KRAMER: SIMPLE CREATIVE TECHNOLOGY Technical Specifications 36 13 Technical Specifications Technical specifications of the SV-552 SummitView™ Proce
ADA Requirements 37 14 ADA Requirements When not mounting the SV-552 in a rack, attention must be paid to overhead clearances. Refer to the ADA Stan
KRAMER: SIMPLE CREATIVE TECHNOLOGY ADA Requirements 38 Figure 14: High/Low Forward, Side and Over Obstruction Reach Limit Requirements
SV-552 SummitView™ Essentials Basic System Check List 39 15 SV-552 SummitView™ Essentials Basic System Check List Remove this list from the user man
Kramer Electronics, Ltd. Web site: www.kramerelectronics.com E-mail: [email protected] P/N: 2900-000603 REV 3 For the latest information on our
Introduction 1 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affo
KRAMER: SIMPLE CREATIVE TECHNOLOGY Overview 2 PART I Your SummitView™ System PART I describes the SummitView™ system and its devices 3 Overview We
Overview 3 • MT-P9P 9” and MT-P6P 6” center pole sections for the SV-1 Mounting Box which can be attached to any 1.5NFS projector mounting system •
KRAMER: SIMPLE CREATIVE TECHNOLOGY Overview 4 However, since the use of UTP cable might not conform to electromagnetic standards, Kramer does not co
Overview 5 Description 5 Connect the appropriate wiring—STP, BC-DGKat524 or BC-DGKat-623, and BCP-2S-25—from the wall plates and the room controll
Comments to this Manuals