Kramer Electronics VM-114H2C User Manual Page 22
- Page / 25
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
VM-114H2C - Protocol 2000
19
10 Protocol 2000
This RS-232/RS-485 communication protocol uses four bytes of information as
defined below.
For RS-232, a null-modem connection between the machine and controller is
used. The default data rate is 9600 baud, with no parity, 8 data bits and 1 stop bit.
Note: Compatibility with Kramer’s Protocol 2000 does not mean that a machine
uses all of the commands below. Each machine uses a sub-set of Protocol 2000,
according to its needs.
10.1 Syntax
MSB
LSB
1st Byte
DESTINATION
INSTRUCTION
0
D
N5
N4
N3
N2
N1
N0
7
6
5
4
3
2
1
0
2nd Byte
INPUT
1
I6
I5
I4
I3
I2
I1
I0
7
6
5
4
3
2
1
0
3rd Byte
OUTPUT
1
O6
O5
O4
O3
O2
O1
O0
7
6
5
4
3
2
1
0
4th Byte
MACHINE NUMBER
1
OVR
X
M4
M3
M2
M1
M0
7
6
5
4
3
2
1
0
1st Byte: Bit 7 – Defined as 0
D – DESTINATION:
0 – Sends information to the switchers (from the PC)
1 – Sends information to the PC (from the switcher)
N5…N0 – INSTRUCTION
The 6-bit INSTRUCTION defines the function performed by the switcher(s). If a function is performed using the
machine’s keyboard, these bits are set with the INSTRUCTION NO. performed. The instruction codes are defined
according to the table below (INSTRUCTION NO. is the value set in N5…N0).
2nd Byte: Bit 7 – Defined as 1
I6…I0 – INPUT
When switching (i.e. instruction codes 1 and 2), the 7-bit INPUT is set as the input number to be switched. If switching is
done using the machine’s front panel, these bits are set with the INPUT NUMBER switched. For other operations, these
bits are defined according to the table.
3rd Byte: Bit 7 – Defined as 1
O6…O0 – OUTPUT
When switching (i.e. instruction codes 1 and 2), the 7-bit OUTPUT is set as the output number to be switched. If
switching is done using the machine’s front panel, these bits are set with the OUTPUT NUMBER switched. For other
operations, these bits are defined according to the table.
4th Byte: Bit 7 – Defined as 1
Bit 5 – Don’t care
OVR – Machine number override
M4…M0 – MACHINE NUMBER
This byte is used to address machines in a system by their machine numbers. When several machines are controlled
from a single serial port, they are usually configured together and each machine has an individual machine number. If
the OVR bit is set, then all machine numbers accept (implement) the command and the addressed machine replies.
When a single machine is controlled over the serial port, always set M4…M0 to 1, and make sure that the machine itself
is configured as MACHINE NUMBER = 1.
- USER MANUAL 1
- VM-114H2C – Contents 3
- 1 Introduction 4
- 2 Getting Started 5
- 2.2 Safety Instructions 6
- 3 Overview 7
- 3.3 Defining the VM-114H2C 8
- Section 5.2) 9
- 4 Connecting the VM-114H2C 10
- 5 Operating the VM-114H2C 12
- 7 Technical Specifications 19
- VM-114H2C 20
- 9 Default EDID 21
- 10 Protocol 2000 22
- VM-114H2C - Protocol 2000 23
- SAFETY WARNING 25
Related products and manuals for Video line amplifiers Kramer Electronics VM-114H2C
(23 pages)Whirlpool FGP300JN0 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Öfen Whirlpool FGP300JN0.
Wir stellen 1 PDF-Handbücher Whirlpool FGP300JN0 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comments to this Manuals